adding oil LAND ROVER DISCOVERY 1995 Workshop Manual

54FRONT AXLE AND FINAL DRIVE
6
OVERHAUL Swivel assembly components
1. Swivel pin housing
2. Top swivel pin and brake hose bracket
3. Upper and lower swivel pin bearings
4. Shim
5. Retaining plate and washer
6. Oil seal
7. Joint washer
8. Swivel bearing housing
9. Joint washer
10. Lower swivel pin
11. Mudshield bracket
12. Swivel housing inner oil sealCheck and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to ball joint bore and pull
balance to determine effort required to turn
swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit to
78 Nm,
and bend over lock tabs.
49.Apply recommended grease between lips of
swivel oil seal.
50.Fit oil seal, joint washer and retaining plate with
seven bolts and spring washers to
11 Nm.
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten to
40 Nm.
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11 Nm.
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.

54FRONT AXLE AND FINAL DRIVE
10
OVERHAUL
40.With seal lips trailing press axle shaft oil seal
flush into rear of housing. Grease lips.
41.Fit new thrust washers and bearing into top
swivel pin bush.
42.Hang swivel pin bearing housing oil seal and
retainer plate over back of housing. Ensure they
are in correct assembly order.
43.Fit a new joint washer and secure swivel pin
bearing housing to axle. Starting with top fixing
dowel bolt. Tighten to
72Nm.
Fit swivel pin housing
44.Grease and fit lower swivel pin bearing to
bearing housing.
45.Place swivel pin housing in position over swivel
pin bearing housing.
46.Using a new joint washer, fit lower swivel pin
with lip outboard. Do not secure with screws at
this stage.
47.Fit a new sensor bush and new oil seal, lip side
leading to top swivel pin.
48.Lubricate with a recommended oil and fit top
swivel pin with existing shims.
49.Coat threads of top swivel pin bolts with Loctite
542. Fit bolts and jump hose bracket (do not
tighten).50.Coat threads of lower swivel pin screws with
Loctite 270 and fit, together with damper and
shield bracket. Tighten to
25 Nm.
51.Tighten top swivel pin and brake jump hose
bracket securing bolts to
65 Nm.
Check and adjust preload on bearings
52.The preload on bearings to be0,25 to 0,30 mm,
withoutswivel housing oil seal and axle fitted,
and reading from centre of swivel pin. The
torque required to turn swivel assembly from
lock to lock to be
2.0 to 2.8 Nm.Adjust by
removing or adding shims as necessary.
53.To take a reading use special tool LRT-57-024
torque test adaptor, with a torque wrench and
extension as shown.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11Nm.
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.